In this article we look at a BH1745NUC Luminance and Colour Sensor and connect it to an Wemos Lolin32
The BH1745NUC is digital color sensor IC with I²C bus interface. This IC senses Red, Green and Blue light (RGB) and converts them to digital values. The high sensitivity, wide dynamic range and excellent Ircut characteristics makes this IC the most suitable to obtain the illuminance and color temperature of ambient light for adjusting LCD backlight of TV, mobile phone and tablet PC. It is possible to detect very wide range light intensity. (0.005 – 40k lx)
Specifications:
VCC Voltage Range: 2.3V to 3.6V
Maximum Sensitivity: 0.005Lx/step
Current Consumption: 130μA (Typ)
Standby Mode Current: 0.8μA (Typ)
Operating Temperature Range: -40°C to +85°C
Features
The High Sensitivity and Wide Dynamic Range (0.005 – 40k lx)
Supports Low Transmittance (Dark) Window
Correspond to I²C Bus Interface
Low Current by Power Down Function
Rejecting 50Hz/60Hz Light Noise
Correspond to 1.8V Logic Interface
Programmable Interrupt Function
It is possible to select 2 type of I²C bus slave address (ADDR =’L’: “0111000”, ADDR =’H’: “0111001”)
Here is a typical module that I used
Parts Required
I connected a Wemos ESP32 (Lolin32) and then the sensor via connecting wire
Name | Link | |
ESP32 | ||
BH1745NUC | ||
Connecting cables |
Schematic/Connection
Be careful as I used a CJMCU-1745 – the sensor is rated at 2.3V to 3.6V. So use the 3.3v out
ESP32 | Sensor |
3.3v | VIN |
Gnd | Gnd |
SDA/21 | SDA |
SCL/22 | SCL |
Code Example
This is a controleverything example – they have code examples for various platforms
#include <Wire.h> // I2C address of the BH1745NUC #define Addr 0x38 void setup() { // Initialise I2C communication as MASTER Wire.begin(); // Initialise serial communication, set baud rate = 9600 Serial.begin(9600); // Start I2C Transmission Wire.beginTransmission(Addr); // Select mode control register1 Wire.write(0x41); // Set RGBC measurement time 160 msec Wire.write(0x00); // Stop I2C Transmission Wire.endTransmission(); // Start I2C Transmission Wire.beginTransmission(Addr); // Select mode control register2 Wire.write(0x42); // Set measurement mode is active, gain = 1x Wire.write(0x90); // Stop I2C Transmission Wire.endTransmission(); // Start I2C Transmission Wire.beginTransmission(Addr); // Select mode control register3 Wire.write(0x44); // Set default value Wire.write(0x02); // Stop I2C Transmission Wire.endTransmission(); delay(300); } void loop() { unsigned int data[8]; for(int i = 0; i < 8; i++) { // Start I2C Transmission Wire.beginTransmission(Addr); // Select data register Wire.write((80+i)); // Stop I2C Transmission Wire.endTransmission(); // Request 1 byte of data from the device Wire.requestFrom(Addr, 1); // Read 8 bytes of data // Red lsb, Red msb, Green lsb, Green msb, Blue lsb, Blue msb // cData lsb, cData msb if(Wire.available() == 1) { data[i] = Wire.read(); } delay(300); } // Convert the data int red = ((data[1] & 0xFF) * 256) + (data[0] & 0xFF); int green = ((data[3] & 0xFF) * 256) + (data[2] & 0xFF); int blue = ((data[5] & 0xFF) * 256) + (data[4] & 0xFF); int cData = ((data[7] & 0xFF) * 256) + (data[6] & 0xFF); // Output data to serial monitor Serial.print("Red Color luminance : "); Serial.println(red); Serial.print("Green Color luminance : "); Serial.println(green); Serial.print("Blue Color luminance : "); Serial.println(blue); Serial.print("Clear Data Color luminance : "); Serial.println(cData); }
Output
Open the serial monitor and you should see something like the following
Red Color luminance : 0
Green Color luminance : 0
Blue Color luminance : 55
Clear Data Color luminance : 65
Red Color luminance : 57
Green Color luminance : 9
Blue Color luminance : 5
Clear Data Color luminance : 7
Place different colored objects beside the sensor and check the values